Toyota Supra A80 Spare Parts

Spare parts for Toyota Supra models built from 1993 to 2002 including JZA80. Covers factrory standards SZ-R, Twin Turbo and RZ variants.

Toyota Interior Trim Panel Fastener Clip Pack TH0362

Toyota screw mounting grommet clip pack to suit various Toyota models - Corolla, Celica, Carina, Corona, Land Cruiser, Prado and  MR2.

These clips have a 13mm top head, 16mm centre head and 18mm collar diameter, 14mm stem length and fit to a 9mm hole and are a plastic push in trim clips used to fasten interior panels such as door cards, trim panels, door pillars, boot linings and pillars.

 Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Supra

  • JZA80

Toyota MR2

  • SW20, SW21
  • ZZW30

Toyota GR Four Yaris 

  • GXPA16

Toyota Corolla

  • AE101, AE102, CE100, EE100, EE101
  • AE110, AE111, AE112, AE114, CDE110, CE110, CE113, CE114, CE116, EE110, EE111, WZE110, ZZE110, ZZE111, ZZE112
  • CDE120, NDE120, ZRE120, ZZE120, ZZE121, ZZE122, ZZE123
  • ZZE130
  • AZE141, CE140, NZE141, ZRE141, ZRE142, ZRE143, ZZE141, ZZE142
  • NDE150, NRE150, ZRE151, ZRE152, ZRE153, ZZE150
  • NRE181, ZRE182 and ZWE182

Toyota Celica

  • ZZT230 and ZZT231

 Toyota Carina

  • ST160, ST162 and ST163

Toyota Corona

  • AT190, CT190, CT195, ST190, ST191, ST195
  • AT210, AT211, CT210, CT211, CT215, CT216, ST210, ST215
  • AT220, CT220 and ST220

Toyota Hilux

  • GRN210, GRN215, KDN215, KZN215, RZN210, RZN215, TRN210, TRN215, UZN210, UZN215, VZN210 and VZN215

Toyota Land Cruiser 

  • FZJ71, FZJ76, FZJ78, FZJ79, GRJ71, GRJ76, GRJ78, GRJ79, HDJ79, HZJ71, HZJ76, HZJ78, HZJ79, KZJ77, LJ77, LJ79, RJ77, VDJ76, VDJ78, VDJ79
  • FZJ80, HDJ80, HDJ81, HZJ80, HZJ81
  • FZJ100, FZJ105, HDJ100, HDJ101, HZJ105, UZJ100
  • GRJ200, URJ200, URJ202, UZJ200 and VDJ200

Toyota Prado

  • GRJ120, GRJ121, GRJ125, KDJ120, KDJ121, KDJ125, KZJ120, LJ120, LJ125, RZJ120, RZJ125, TRJ120, TRJ125, VZJ120, VZJ121, VZJ125
    GDJ150, GDJ151, GDJ155, GRJ150, GRJ151, GRJ152, KDJ150, KDJ155, LJ150, TRJ150, TRJ152 and TRJ155

Toyota Soarer

  • UZZ40

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

Toyota Supra JZA80 Floor Mat Set LHD

Front and rear floor carpetset for your left hand drive fourth generation A80 series Toyota Supra.

Suited to all LHD Toyota Supra JZA80 built between 1993 to 2002 our carpet floor mats are well fitting and made in Australia to the highest quality with a non-slip foam backing.

Available in loop or plush pile and fourteen different colours. Just use the drop down menus to select pile and colour.

NOTE: Colour swatches shown are on plush pile carpet and may differ slightly on loop.

Complete your 'fourth gen' Toyota Supra project in style - whether its a retro-ride, drift car, daily driver or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

$170.00
* Carpet Colour:

* Carpet Pile:

* Edge Binding Colour:

JZA80 Toyota Supra OEM side markers

Complete your JZA80 Toyota Supra project in style with these genuine OEM side markers.

Fitted to the fender these side marker units suit 'face lift' versions of the JZA80 Toyota Supra built 1995 to 2002.

Ideal for a giving your Supra a 'make-over' , maintaining road worthiness or for the complete genuine resto.

Sold as a pair, they will look great on a vintage restoration, retro ride, resto mod, drift machine or every day driver.

Shipping worldwide every week - no problems for international buyers.

$80.00
Out of stock

JZA80 Toyota Supra OEM front indicator parker lights

Complete your A80 series Supra project in style with these genuine OEM front indicator parker lights.

These tail light units suit 'face lift' versions of the A80 series built 1996 to 2002.

Ideal for a giving your Supra a 'make-over' , maintaining road worthiness, for the complete genuine resto or keep a pair 'just in case'.

Sold as a pair, they will look great on a vintage restoration, retro ride, resto mod, drift machine or every day driver.

Shipping worldwide every week - no problems for international buyers.

$300.00
Out of stock

Toyota Front and Rear Bumper Bar 9mm Clips Pack (TH0521)

Bumper cover fastener clip pack to suit various Toyota models - Celica, MR2, Supra and Soarer.

These clips are used to fasten front and rear bumpers into place. 

These are a push in clip that expands when the 9mm head is pushed in and holds firmly in place.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica (front bumper)

  • AT180, ST182, ST183, ST184 and ST185

Toyota MR2 (front bumper)

  • SW20 and SW21

 Toyota Supra (front and rear bumper)

  • JZA80

Toyota Soarer (front and rear bumper)

  • JZZ30, JZZ31, UZZ30, UZZ31 and UZZ32

 Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

Toyota Supra JZA80 Boot (Trunk) Mat

Carpet mat for the boot (trunk) area of your fourth generation A80 series Toyota Supra.

Suited to all Toyota Supra JZA80 built between 1993 to 2002 our carpet boot mats are well fitting and made in Australia to the highest quality with a non-slip foam backing.

Available in loop or plush pile and fourteen different colours. Just use the drop down menus to select pile and colour.

NOTE: Colour swatches shown are on plush pile carpet and may differ slightly on loop.

Complete your 'fourth gen' Toyota Supra project in style - whether its a retro-ride, drift car, daily driver or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

$185.00
* Carpet Pile:

* Carpet Colour:

* Edge Binding Colour:

JZA80 Toyota Supra OEM rear quarter clearance markers

Complete your Toyota Supra A80 Series (JZA80) project in style with these genuine OEM rear quarter clearance side markers.

Fitted to the rear quarter fender of the Toyota Supra JZA80 these side marker units suit 'face lift' versions built 1995 to 2002.

Ideal for a giving your Toyota Supra JZA80 a 'make-over' , maintaining road worthiness, completing a genuine restoration or keeping one 'just in case'.

Sold as a pair, they will look great on a vintage restoration, retro ride, resto mod, drift machine or every day driver.

Shipping worldwide every week - no problems for international buyers.

$125.00
Out of stock

TMC Build Plate Models built after 1980 all markets

Complete your Toyota restoration project in style with a reproduction Toyota (TMC) Build Plate for vehicles built after 1980.

These TMC Build Plates were fitted in the engine bay of all early model Toyota's built from the 1980's right up until recent years - this may vary on some models.

We have seen these on Celica, Supra, MR2, Soarer, Corolla, Aristo, Starlet, Hilux and Landcruiser just to name a few models.

You may find that your original plate is missing (these are not a VIN!) as an owner may have removed it for painting of sometimes they have corroded and are no longer legible.

The plate was used to inform the production line workers as to what model engine was to be fitted to the vehicle - part of Toyota's quality program!

Our reproduction part is exacting in every detail. 

The pricing includes having your car's data applied to the plate before we ship it to you.

We ship globally to all countries weekly.

$80.00

Toyota 2JZ-GTE 5mm Ignition Lead Kit (TH56744)

Genuine Eagle brand 5mm ignition leads to suit your Toyota Soarer fitted with a 2JZ-GTE engine.

Our photo shows each of the boot and tube assemblies specific to this kit that suits the 2JZ-GTE engines.

Suits 3.0L 2JZ-GTE DOHC 24V Supra models as follows:

  • JZA80 Twin Turbo

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

  • Hi-temp Silicone Well Cover boot
  • PVT insulator tube insulates plug terminal to prevent high voltage crossover
  • Hi-temp Silicone Tip Seal.

Terminal Features

  • High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
  • Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
  • Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

  • Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
  • High Dielectric Silicone inner jacket.
  • Technologically advanced nylon tape adds tensile strength.
  • 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

$115.00

Toyota Bonnet Hood Insulation Clip Pack (TH0500)

Toyota bonnet (hood) insulation clip pack to suit various Toyota models - Celica, Corolla, Hilux, Surf, Prado, Soarer and Supra

These clips have a 24.5mm head are used with a 7mm hole and are plastic push in trim clips used to fasten the under bonnet (hood) insulation sheet. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

  • ZZT230 and ZZT231

Toyota Supra

  • JZA80

Toyota Corolla

  • AE101, CE101, CE102, CE105, CE107
  • AE111, AE115, CDE110, CE113, CE116, WZE110, ZZE11, ZZE112
  • CDE120, NDE120, ZRE120, ZZE120, ZZE121 and ZZE122

Toyota Hilux / Surf

  • GRN210, GRN215, KDN215, KZN215, RZN210, RZN215, TRN210, TRN215, UZN210, UZN215, VZN210 and VZN215

Toyota Prado

  • GRJ120, GRJ121, GRJ125, KDJ120, KDJ121, KDJ125, KZJ120, LJ120, LJ125, RZJ120, RZJ125, TRJ120, TRJ125, VZJ120, VZJ121 and VZJ125

 Toyota Soarer

  • JZZ30, JZZ31, UZZ30, UZZ31, UZZ32
  • UZZ40

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

JZA80 Toyota Supra OEM Genuine Tail Lights

Complete your JZA80 Toyota Supra project in style with these genuine OEM tail lights.

These tail light units suit 'face lift' versions of the JZA80 Toyota Supra built 1995 to 2002.

Ideal for a giving your JZA80 Toyota Supra a 'make-over', maintaining road worthiness, for the complete genuine resto or keep a pair 'just in case'.

Sold as a pair, they will look great on a detailed restoration, retro ride, resto mod, drift machine or every day driver.

Shipping worldwide every week - no problems for international buyers.

$400.00
1 In Stock

Toyota Bonnet (Hood) Weather Strip Clips Pack (TH0391)

Radiator support to bonnet (hood) rubber seal fastener clip pack to suit various Toyota models - Celica, Corolla, Corona, Cressida, Land Cruiser, MR2, Hilux, Starlet and Supra

These clips are used to fasten the rubber strip that sits between the bonnet (hood) underside and top of the radiator support panel to reduce wind and water coming into the under bonnet (hood) area. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

  • TA40, TA45, TA41, TA42, TA46, TA47, RA40, RA45, RA55, RA46, RA42 and RA43
  • TA60, TA61, AA63, TA62, TA63, TA64, SA60, RA63, RA60, RA6, SA63, RA64 and RA65
  • ST160, ST162, AT160, ST163, ST164 and ST165
  • ST180, ST184 and ST185
  • ST200, ST202, ST203, ST204 and ST205

Toyota Corolla

  • All models from KE30 through to ZWE182

 Toyota Corona

  • All models from ST140 through to ST215

Toyota Cressida

  • All models from MX32 through to RX81

Toyota Hilux and Surf

  • All models from LN130 through to VZN185

Toyota Land Cruiser

  • All models from BJ60 through HZJ105

Toyota MR2

  • AW10 andAW11
  • ZZW30

 Toyota Supra

  • GA70, JZA70 and MA70
  • JZA80

Toyota Starlet

  • KP60, KP61

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

Toyota 2JZ-GE 5mm Ignition Lead Kit (TH56228)

Genuine Eagle brand 5mm ignition leads to suit your Toyota Supra fitted with a 2JZ-GE engine.

Our photo shows each of the boot and tube assemblies specific to this kit that suits the 2JZ-GE engines.

Suits 3.0L 2JZ-GE DOHC 24V Supra models as follows:

  • JZA80 

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

  • Hi-temp Silicone Well Cover boot
  • PVT insulator tube insulates plug terminal to prevent high voltage crossover
  • Hi-temp Silicone Tip Seal.

Terminal Features

  • High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
  • Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
  • Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

  • Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
  • High Dielectric Silicone inner jacket.
  • Technologically advanced nylon tape adds tensile strength.
  • 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

$202.50

Toyota Bumper and Grille Clip Pack (TH0365)

Toyota bumper and grille clip pack to suit various Toyota models - Supra, MR2, Corolla and Celica.

These clips have a 19mm head, 26mm stem length and fit to a 8.5mm hole and are a plastic push in trim clips used to fasten radiator covers, front grille, front bumper bar, rear bumper bar and seat tracks.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Supra

  • JZA80

Toyota MR2

  • SW20, SW21
  • ZZW30

 Toyota Corolla

  • AE100 and AE101

Toyota Celica

  • AT200, ST202, ST203, ST204 and ST205

 Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

JZA80 Toyota Supra Front Sway Bar Kit

Improve handling and performance of your fourth generation A80 Toyota Supra (JZA80) with a custom rear Sway Bar.

Toyota Heritage sway bars are Australian made, two-hole adjustable and powder coated to the highest standards.

The standard size front sway bar we offer for the JZA80 Toyota Supra is 35mm (rear) finished in red powder coat. Ideal for street and track with increased torsional stiffness of 15% to 30% over factory sized bars.

Our JZA80 Toyota Supra rear sway bar comes complete with bushes, brackets, links and lateral locks.

We offer the opportunity for buyers to customise their sway bar by selecting the size required in the drop down menu 'Sway Bar Size'.

Buyers can select their desired sway bar thickness starting at 28mm and up to 35mm (or even thicker if required).

We ship worldwide weekly - no problems for overseas buyers.

$399.00

Toyota Interior Trim Clip Pack TH0361

Interior trim clip pack to suit various Toyota models - Celica, Camry, Corolla, Corona, Cressida, Soarer, Starlet and Supra

These clips are

Used with a 6.6mm hole and are plastic push in trim clips used to fasten interior trim sections to the inner body work and on some models they are used to fasten bumper sections to the main bumper cover. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

  • ST180, ST184 and ST185

Toyota Supra

  • JZA80

Toyota Corolla

  • AE100, AE101, AE102, AE104, CE100, CE104, CE106, CE108, CE109, EE100, EE101, EE102, EE103, EE104, EE105, EE106, EE107 and EE108

 Toyota Corona

  • AT177, CT176, CT177 and ET176

Toyota Camry

  • CV10, CV11, SV10, SV11 and SV12

Toyota Starlet

  • EP70, EP71, EP76 and NP70

Toyota Soarer

  • UZZ40 

Toyota Cressida

  • GX70, LX76, YX76 and YX78

Toyota Carina

  • AT150, AT151, CT150, ST150
  • AT160, ST162
  • CT176, ET176
  • ST180, ST181, ST182 and ST183

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

JZA80 Toyota Supra Rear Sway Bar Kit

Improve handling and performance of your fourth generation A80 Toyota Supra (JZA80) with a custom rear Sway Bar.

Toyota Heritage sway bars are Australian made, three-way adjustable and powder coated to the highest standards.

The standard size rear sway bar we offer for the JZA80 Toyota Supra is 24mm (rear) finished in red powder coat. Ideal for street and track with increased torsional stiffness of 15% to 30% over factory sized bars.

Our JZA80 Toyota Supra rear sway bar comes complete with bushes, brackets, links and lateral locks.

We offer the opportunity for buyers to customise their sway bar by selecting the size required in the drop down menu 'Sway Bar Size'.

Buyers can select their desired sway bar thickness starting at 18mm and up to 25mm (or even thicker if required).

We ship worldwide weekly - no problems for overseas buyers.

$335.00
* Rear Sway Bar Diameter:

Toyota Supra JZA80 Floor Mat Set RHD

Front and rear floor carpetset for your fourth generation A80 series Toyota Supra.

Suited to all RHD Toyota Supra JZA80 built between 1993 to 2002 our carpet floor mats are well fitting and made in Australia to the highest quality with a non-slip foam backing.

Available in loop or plush pile and fourteen different colours. Just use the drop down menus to select pile and colour.

NOTE: Colour swatches shown are on plush pile carpet and may differ slightly on loop.

Complete your 'fourth gen' Toyota Supra project in style - whether its a retro-ride, drift car, daily driver or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

$170.00
* Carpet Colour:

* Carpet Pile:

* Edge Binding Colour:

JZA80 Toyota Supra Radiator Cooling Panel

Improve performance with better cooling of your fourth generation A80 Toyota Supra (JZA80) with a custom radiator cooling panel.

Toyota Heritage radiator cooling panels are Australian made, light weight aluminium and are anodised to the highest standards.

These JZA80 Toyota Supra cooling panels are finished in your choise of silver, black or red anodise. Fitted to the top of bumper and back to the radiator top these panels are ideal for street and track with increased airflow for colling efficiency of around 50% better than factory set up with no panel..

Buyers can select their desired colour simply by using the drop down menu.

We ship worldwide weekly - no problems for overseas buyers.

$99.00
* Colour - Anodise:

Toyota Door Card Side Trim Panel and Fascia Clips Pack TH0379

Door card, side trim panel and fascia fastener clip pack to suit various Toyota models - Caldina, Celica, Corolla, Corona, Supra, MR2, Soarer, Prado, Yaris, Hilux and Land Cruiser.

These clips are used to fasten side and rear door cards to the door as well as other interior trim and fascia panels.

These are a push in clip that have a fit to a 9mm hole size and measure 12.8mm ( top head diameter), 15.6mm (centre head diameter) , 17.7mm (bottom head diameter) with a stem length of 14.2mm.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Caldina

  • AT191, CT190, CT196, CT197, CT198, CT199, CT216, ET196, ST190, ST191, ST195, ST198
  • AT211, ST210, ST215

 Toyota Celica 

  • ST200, ST202, ST203, ST204 and ST205

Toyota Corolla

  • AE91, AE92, AE95, CE90, EE90
  • AE100, AE101, AE102, AE103, AE104, CE100, CE101, CE104, EE100, EE101
  • AE110, AE111, AE112, AE114, AE115, CDE110, CE110, CE113, CE114, CE116, EE110, EE111, WZE110, ZZE111, ZZE112
  • CDE120, ZRE120, ZZE120, ZZE121, ZZE122 and ZZE123

 Toyota Corona

  • YT140

 Toyota Hilux

  • KDN145, LN140, LN141, LN145, LN147, RZN142, RZN144, RZN147, RZN148, RZN149
  • KDN150, KDN151, LN150, LN152,
  • KDN165, KDN166, KZN165, LN166, LN167
  • KDN170, LN170, LN171, LN172, RZN173, RZN174, VZN172
  • KDN190, KZN190, LN192 and RZN194

  Toyota Supra

  • MA61, MA63

Toyota Land Cruiser 

  • BJ60, FJ62, HJ60
  • BJ73, FJ70, FJ73, FJ75, FZJ70, FZJ71, FZJ73, FZJ74, FZJ75, FZJ78, FZJ79, HDJ78, HDJ79, HJ75, HZJ70, HZJ71, HZJ73, HZJ74, HZJ75, HZJ76, HZJ77, HZJ78, HZJ79, KZJ70, KZJ71, KZJ73, KZJ77, KZJ78, LJ70, LJ71, LJ72, LJ73, LJ77, LJ78, LJ79, PZJ70, PZJ73, PZJ75, PZJ77, RJ70, RJ73, RJ77
  • FJ80, FZJ80, HDJ80, HDJ81, HZJ80, HZJ81
  • FZJ100, FZJ105, HDJ100, HDJ101, HZJ105 and UZJ100

Toyota Prado

  • KDJ90, KDJ95, KZJ90, KZJ95, LJ90, LJ95, RZJ90, RZJ95, VZJ90 and VZJ95

Toyota MR2 

  • SW20 and SW21

Toyota Soarer

  • JZZ30, UZZ30, UZZ31 and UZZ32

Toyota Supra

  • JZA80

Toyota Yaris 

  • NCP10, NCP11, NCP12, NCP13, NLP10, SCP10
  • NCP20
  • EP80, EP81, EP82, EP85, NP80
  • EP90, EP91, EP95 and NP90

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size: