Toyota Crown S80 S90 S100 Series Parts

Spare parts for Toyota Crown including RS80, RS90 and RS100

Toyota 5ME 9mm lead kit (TH9618)

Genuine Eagle brand 9mm ignition leads to suit your Toyota Celica XX, Toyota Celica Supra, Toyota Cressida or Toyota Crown fitted with a 5ME engine.

Our photo shows each of the boot and tube assemblies specific to this kit that suits the 5ME engines.

Suits 2.8L 5ME SOHC Celica XX , Celica Supra, Cressida and Crown models as follows:

  • MA47 - Celica XX
  • MA56 - Celica XX and Celica Supra
  • MA61 - Celica Supra
  • MX62 - Cressida
  • MX73 - Cressida
  • MS112 and MS123 - Crown

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

  • Hi-temp Silicone Well Cover boot
  • PVT insulator tube insulates plug terminal to prevent high voltage crossover
  • Hi-temp Silicone Tip Seal.

Terminal Features

  • High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
  • Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
  • Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

  • Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
  • High Dielectric Silicone inner jacket.
  • Technologically advanced nylon tape adds tensile strength.
  • 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

$127.50

Toyota M Engine 9mm Ignition Lead Kit (TH9616)

Genuine Eagle brand 9mm ignition leads to suit your Toyota Corona Mark ii or Toyota Crown fitted with an M or 2M engine.

Our photo shows each of the boot and tube assemblies specific to this kit that suits the M and 2M engines.

Suits 2.0L M SOHC Corona models as follows:

  • MX10, MX20 and MX27

Suits 2.3L 2M SOHC Corona models as follows:

  • MX12, MX22 and MX28

Suits 2.6L 4M SOHC Corona and Crown models as follows:

  • Corona - MX13 and MX23
  • Crown - MS65, MS83, MS85 and MS111

 General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

  • Hi-temp Silicone Well Cover boot
  • PVT insulator tube insulates plug terminal to prevent high voltage crossover
  • Hi-temp Silicone Tip Seal.

Terminal Features

  • High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
  • Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
  • Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

  • Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
  • High Dielectric Silicone inner jacket.
  • Technologically advanced nylon tape adds tensile strength.
  • 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

$120.50

Toyota Crown S80 S90 and S100 Series Moulded Carpet Set

Front and rear moulded floor carpet for your fifth generation S80, S90 or S100 series Toyota Crown. 

Suited to all Toyota Crown S80, S90 or S100 series built between 1974 to 1979 our moulded carpets are well fitting and made in Australia to the highest quality and replace original parts 58510-30310 (front driver side), 58520-30850 (front passenger side), 58513-30140 (trans tunnel) and 58540-30141 (rear floor).

Suits all sedan and wagon models in the series including MS80, MS90, MS100, RS80, RS90 and RS100.

Available in loop or plush pile and fourteen different colours. Just use the drop down menus to select pile and colour.

NOTE: Colour swatches shown are on plush pile carpet and may differ slightly on loop.

Complete your 'fourth gen' Toyota Crown project in style - whether its a retro-ride, daily driver or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

 

$240.00
* Carpet Colour:

* Carpet Pile:

Toyota Crown Build Plate MS85

Reproduction build plate to suit your fifth generation MS85 Toyota Crown.

Suited to all Toyota Crown MS85 these build plates are faithful reproductions made in Australia to the highest quality.

These build plates were fitted to the inner fender (mud guard) or some times the firewall of the MS86 Toyota Crown fitted with 4M engines and built between 1975 to 1979.

Complete your 'old school' Toyota Crown project in style - whether its a retro-ride, drift pig, daily driver, restoration project or even a wedding hire car!

These build plates have been manufactured using precision tooling to produce a high quality faithful reproduction item.

Shipping worldwide weekly - no problems for overseas buyers.

$80.00

TEQ Build Plate Early Models to 1974 Japan Delivery

Complete your early Toyota restoration project in style with a reproduction Toyota (TEQ) Build Plate for vehicles with original delivery in Japan.

These TEQ Build Plates were fitted in the engine bay of all early model Toyota's built during the mid and late 1960's and early 1970's. Generally these were used up till December 1974, but this may vary on some models.

We have seen these on Crown, Corolla, Corona, Mark ii, Stout, Publica, Hilux and Landcruiser just to name a few models.

You may find that your original plate is missing (these are not a VIN!) as an owner may have removed it for painting of sometimes they have corroded and are no longer legible.

The plate was used to inform the production line workers as to what model engine was to be fitted to the vehicle - part of Toyota's quality program!

Our reproduction part is exacting in every detail. 

The pricing includes having your car's data applied to the plate before we ship it to you.

We ship globally to all countries weekly.

$80.00

Toyota 4M Engine Valve Clearance Decal

Reproduction valve clearance decal for Toyota models with 4M engines.

Suits models with 4M engines as follows:

  • Toyota Crown MS65, MS68V, MS75
  • Toyota Crown MS80, MS90, MS100
  • Toyota Mark ii MX12, MX22, MX28, MX32, MX36

These decals were fitted to the side of the rocker cover from the factory and provided data for valve clearances.

Our reproduction part is exacting in every detail. 

Shipping worldwide weekly - no problems for overseas buyers.

$10.00