Toyota Celica T180 Series

Spare parts for Toyota Celica including ST180, AT180, ST182, ST183, ST184, ST185

Toyota Inner Guard (Fender) Fastener Clip Pack (TH0385)

Inner guard (fender) fastener clip pack to suit various Toyota models - Celica, Corolla, Camry, MR2, Carina, Caldina

These clips are used to fasten inner guards (fenders) to the outer guard and are screwed into place. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

  • TA40, TA45, TA41, TA42, TA46, TA47, RA40, RA45, RA55, RA46, RA42 and RA43
  • TA60, TA61, AA63, TA62, TA63, TA64, SA60, RA63, RA60, RA6, SA63, RA64 and RA65
  • ST160, ST162, AT160, ST163, ST164 and ST165
  • ST180, ST184 and ST185
  • ST200, ST202, ST203, ST204 and ST205

 Toyota MR2

  • AW10 and AW11
  • SW20 and SW21
  • ZZW30

Toyota GR Four Yaris

  • GXPA16

Toyota Corolla

  • AE81, AE82, AE85 and AE86
  • AE90, AE92, AE93, AE94, AE95 and AE96
  • AE101, AE102 and AE112 

 Toyota Camry

  • SV10, SV11, SV12, CV10 and CV11
  • SV20, SV21 and SV22

Toyota Caldina 

  • ST191, ST195 and ST198

 Toyota Carina

  • TA40, TA41, TA42, TA47, TA57, RA40, RA45, RA46, RA55 and RA56
  • AA60, KA67V, AA63, TA60, TA61, TA67V, TA62, TA63, RA63, CA60 and CA67V
  • ST162
  • ET176V, AT170, AT175, ST170, ST170G, CT170, CT170G and CT176V
  • AT192, AT190, AT191, ST190, ST195, CT190 and CT195
  • AAT212, AT210, AT211, ST210, ST215, CT210, CT215, CT211 and CT216

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$25.00
* Pack size:

Toyota Celica T180 Series Floor Mat Set

Front and rear floor carpet set for your T180 series fifth generation Toyota Celica.

Suited to all RHD Toyota Celica T180 series such as AT180, ST180, ST182, ST183 and ST184 built between 1989 to 1993 our carpet floor mats are patterned off the floor of an original ST183, are well fitting and made in Australia to the highest quality with a non-slip foam backing.

There are four mats included in the set and this includes the two front foot well mats and the two rear floor well mats. 

Displayed here in Black with a black edge binding on the passnger side mats and in Red with red edge binding for the driver side mats, these mats provide a look that has an OEM look and feel.

Available in loop or plush pile and fourteen different colours. Just use the drop down menus to select pile and colour.

NOTE: Colour swatches shown are on plush pile carpet and may differ slightly on loop.

Complete your 'fifth gen' Toyota Celica T180 series project in style - whether its a daily driver, offroader or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

$140.00
* Carpet Pile:

* Carpet Colour:

Toyota Interior Trim Clip Pack TH0361

Interior trim clip pack to suit various Toyota models - Celica, Camry, Corolla, Corona, Cressida, Soarer, Starlet and Supra

These clips are

Used with a 6.6mm hole and are plastic push in trim clips used to fasten interior trim sections to the inner body work and on some models they are used to fasten bumper sections to the main bumper cover. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

  • ST180, ST184 and ST185

Toyota Supra

  • JZA80

Toyota Corolla

  • AE100, AE101, AE102, AE104, CE100, CE104, CE106, CE108, CE109, EE100, EE101, EE102, EE103, EE104, EE105, EE106, EE107 and EE108

 Toyota Corona

  • AT177, CT176, CT177 and ET176

Toyota Camry

  • CV10, CV11, SV10, SV11 and SV12

Toyota Starlet

  • EP70, EP71, EP76 and NP70

Toyota Soarer

  • UZZ40 

Toyota Cressida

  • GX70, LX76, YX76 and YX78

Toyota Carina

  • AT150, AT151, CT150, ST150
  • AT160, ST162
  • CT176, ET176
  • ST180, ST181, ST182 and ST183

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

Toyota Bonnet Hood Insulation Clips (TH0498)

Bonnet (hood) insulation fastener clip pack to suit various Toyota models - Celica, Supra, and Soarer

These clips are used to fasten the bonnet (hood) insulation into place.

These are a push in fastener that has a gloss black 30mm head and 15mm lenth that fits to an 8mm hole.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica 

  • ST182, ST183 and ST184
  • ST204 and ST205

Toyota Soarer

  • GZ20

 Toyota Supra

  • GA70, JZA70 and MA70

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

Toyota Bonnet (Hood) Weather Strip Clips Pack (TH0391)

Radiator support to bonnet (hood) rubber seal fastener clip pack to suit various Toyota models - Celica, Corolla, Corona, Cressida, Land Cruiser, MR2, Hilux, Starlet and Supra

These clips are used to fasten the rubber strip that sits between the bonnet (hood) underside and top of the radiator support panel to reduce wind and water coming into the under bonnet (hood) area. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

  • TA40, TA45, TA41, TA42, TA46, TA47, RA40, RA45, RA55, RA46, RA42 and RA43
  • TA60, TA61, AA63, TA62, TA63, TA64, SA60, RA63, RA60, RA6, SA63, RA64 and RA65
  • ST160, ST162, AT160, ST163, ST164 and ST165
  • ST180, ST184 and ST185
  • ST200, ST202, ST203, ST204 and ST205

Toyota Corolla

  • All models from KE30 through to ZWE182

 Toyota Corona

  • All models from ST140 through to ST215

Toyota Cressida

  • All models from MX32 through to RX81

Toyota Hilux and Surf

  • All models from LN130 through to VZN185

Toyota Land Cruiser

  • All models from BJ60 through HZJ105

Toyota MR2

  • AW10 andAW11
  • ZZW30

 Toyota Supra

  • GA70, JZA70 and MA70
  • JZA80

Toyota Starlet

  • KP60, KP61

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

Toyota Celica ST185 7mm lead kit for GT-Four (TH74577)

Genuine Eagle brand 7mm ignition leads to suit your ST185 Toyota Celica built from 1989 to July 1991.

Our photo shows each of the boot and tube assemblies specific to this kit that suits the ST185 Toyota Celica

Suits 2.0L 3S-GTE DOHC 16V Fuel Injection Turbo models of the ST185 Toyota Celica GT-Four, GT-Four V, GT-Four A, Turbo 4WD, GT-Four RC, GT-Four Grp A Rallye and also referred to as Turbo All-Trac (USA).

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

  • Hi-temp Silicone Well Cover boot
  • PVT insulator tube insulates plug terminal to prevent high voltage crossover
  • Hi-temp Silicone Tip Seal.

Terminal Features

  • High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
  • Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
  • Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

  • Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
  • High Dielectric Silicone inner jacket.
  • Technologically advanced nylon tape adds tensile strength.
  • 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

$88.15

Toyota Door Card Trim Panel Clips Pack TH0176

Door card fastener clip pack to suit various Toyota models - Celica, Corolla, Corona, Supra, Hilux and Land Cruiser.

These clips are used to fasten side and rear door cards to the door.

These are a push in clip that have a fit to a 9mm hole and have a T1 13mm head diameter with a stem length of 14mm.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica 

  • AA63, GA61, RA60, RA61, RA63, RA64, RA65, SA60, SA63, TA60, TA61, TA63, TA64
  • AT160, ST160, ST161, ST162, ST163, ST165 
  • AT180, ST182, ST183, ST184 and ST185

Toyota Corolla

  • KE30, KE35, KE36, KE38, TE31, TE37, TE38
  • TE47
  • KE50, KE55, TE51,
  • AE70, AE71, CE70, CE71, CE72, KE70, KE71, KE72, KE73, KE74, TE70, TE71, TE72, TE73, TE74
  • AE80, AE81, AE82, AE85, AE86, CE80, EE80

 Toyota Corona

  • AT140, AT141, CT140, CT141, CT147, KT147, RT141, ST140, TT142, TT147, YT140

 Toyota Hilux

  • LN50, LN51, LN55, LN56, LN57, RN50, RN55, RN58, YN50, YN51, YN52, YN55, YN56, YN57, YN58
    LN60, LN61, LN65, RN60, RN61, RN66, RN67, VZN61, VZN66, YN60, YN61G, YN61V, YN62, YN63, YN65, YN67
    RN70, RN75

 Toyota Supra

  • MA61, MA63

Toyota Land Cruiser 

  • BJ40, BJ41, BJ42, BJ44, BJ45, BJ46, FJ40, FJ45, HJ47
  • BJ60, BJ61, FJ60, FJ61, FJ62, FJ62G, FJ62V, HJ60, HJ61
  • BJ70, BJ71, BJ73, BJ74, BJ75, FJ70, FJ73, FJ75, HJ75, LJ75, LJ70, LJ71, LJ73, RJ70, RJ73 

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size:

TMC Build Plate Models built after 1980 all markets

Complete your Toyota restoration project in style with a reproduction Toyota (TMC) Build Plate for vehicles built after 1980.

These TMC Build Plates were fitted in the engine bay of all early model Toyota's built from the 1980's right up until recent years - this may vary on some models.

We have seen these on Celica, Supra, MR2, Soarer, Corolla, Aristo, Starlet, Hilux and Landcruiser just to name a few models.

You may find that your original plate is missing (these are not a VIN!) as an owner may have removed it for painting of sometimes they have corroded and are no longer legible.

The plate was used to inform the production line workers as to what model engine was to be fitted to the vehicle - part of Toyota's quality program!

Our reproduction part is exacting in every detail. 

The pricing includes having your car's data applied to the plate before we ship it to you.

We ship globally to all countries weekly.

$75.00

Toyota Celica ST182 GT and ST183 4WS 7mm lead kit for (TH74577)

Genuine Eagle brand 7mm ignition leads to suit your ST182 or ST183 Toyota Celica built from 1989 to 1993.

Our photo shows each of the boot and tube assemblies specific to this kit that suits the  ST182 and ST183 Toyota Celica

Suits 2.0L 3S-GE DOHC 16V Fuel Injection models of the ST182 Toyota Celica GT-R, GT-i and GTS-i 16 and ST183 Toyota Celica 4WS GT-R, Active Sports, 4WS convertible and 4WS convertible Type G.

NOTE: these models were not delivered to the Australian market but you may own a private import. These models were mostly delivered domestically in Japan plus other foreign markets such as New Zealand, Belgium and the Middle East. 

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

  • Hi-temp Silicone Well Cover boot
  • PVT insulator tube insulates plug terminal to prevent high voltage crossover
  • Hi-temp Silicone Tip Seal.

Terminal Features

  • High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
  • Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
  • Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

  • Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
  • High Dielectric Silicone inner jacket.
  • Technologically advanced nylon tape adds tensile strength.
  • 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

$88.15
2 In Stock

Toyota Celica ST185 5mm lead kit for GT-Four (TH54299)

Genuine Eagle brand 5mm Leads to suit your ST185 Toyota Celica built from August 1991 to 1993

Our photo shows each of the boot and tube assemblies specific to this kit that suits the ST185 Toyota Celica.

Suits 2.0L 3S-GTE DOHC 16V Fuel Injection Turbo models of the ST185 Toyota Celica GT-Four, GT-Four V, GT-Four A, Turbo 4WD, GT-Four RC, GT-Four Grp A Rallye and also referred to as Turbo All-Trac (USA).

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

  • Hi-temp Silicone Well Cover boot
  • PVT insulator tube insulates plug terminal to prevent high voltage crossover
  • Hi-temp Silicone Tip Seal.

Terminal Features

  • High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
  • Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
  • Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

  • Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
  • High Dielectric Silicone inner jacket.
  • Technologically advanced nylon tape adds tensile strength.
  • 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

$145.00

Toyota Front and Rear Bumper Bar 9mm Clips Pack (TH0521)

Bumper cover fastener clip pack to suit various Toyota models - Celica, MR2, Supra and Soarer.

These clips are used to fasten front and rear bumpers into place. 

These are a push in clip that expands when the 9mm head is pushed in and holds firmly in place.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica (front bumper)

  • AT180, ST182, ST183, ST184 and ST185

Toyota MR2 (front bumper)

  • SW20 and SW21

 Toyota Supra (front and rear bumper)

  • JZA80

Toyota Soarer (front and rear bumper)

  • JZZ30, JZZ31, UZZ30, UZZ31 and UZZ32

 Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

 

$15.00
* Pack size: