Spare parts suitable for Toyota Celica T160 Series

Door card fastener clip pack to suit various Toyota models - Celica, Corolla, Corona, Supra, Hilux and Land Cruiser.

These clips are used to fasten side and rear door cards to the door.

These are a push in clip that have a fit to a 9mm hole and have a T1 13mm head diameter with a stem length of 14mm.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica 

• AA63, GA61, RA60, RA61, RA63, RA64, RA65, SA60, SA63, TA60, TA61, TA63, TA64
• AT160, ST160, ST161, ST162, ST163, ST165 
• AT180, ST182, ST183, ST184 and ST185

Toyota Corolla

• KE30, KE35, KE36, KE38, TE31, TE37, TE38
• TE47
• KE50, KE55, TE51,
• AE70, AE71, CE70, CE71, CE72, KE70, KE71, KE72, KE73, KE74, TE70, TE71, TE72, TE73, TE74
• AE80, AE81, AE82, AE85, AE86, CE80, EE80

 Toyota Corona

• AT140, AT141, CT140, CT141, CT147, KT147, RT141, ST140, TT142, TT147, YT140

 Toyota Hilux

• LN50, LN51, LN55, LN56, LN57, RN50, RN55, RN58, YN50, YN51, YN52, YN55, YN56, YN57, YN58
  LN60, LN61, LN65, RN60, RN61, RN66, RN67, VZN61, VZN66, YN60, YN61G, YN61V, YN62, YN63, YN65, YN67
  RN70, RN75

 Toyota Supra

• MA61, MA63

Toyota Land Cruiser 

• BJ40, BJ41, BJ42, BJ44, BJ45, BJ46, FJ40, FJ45, HJ47
• BJ60, BJ61, FJ60, FJ61, FJ62, FJ62G, FJ62V, HJ60, HJ61
• BJ70, BJ71, BJ73, BJ74, BJ75, FJ70, FJ73, FJ75, HJ75, LJ75, LJ70, LJ71, LJ73, RJ70, RJ73 

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Headlamp and grille (fender) fastener clip pack to suit various Toyota models - Celica, Corolla, Corona, Carina, Publica, Land Cruiser and Hilux

These clips are used to fasten inner guards (fenders) to the outer guard and are screwed into place. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

• TA40, TA45, TA41, TA42, TA46, TA47, RA40, RA45, RA55, RA46, RA42 and RA43
• ST160, ST162, AT160, ST163, ST164 and ST165

Toyota Corolla

• KE10, KE11, KE15, KE16, KE17 and KE18
• KE20, KE25, TE21, TE25, TE27 and TE26
• KE30, KE35, KE50, KE55, TE31, TE51, KE36 and KE38
• TE72
• AE90, AE91, AE92 and EE90

 Toyota Land Cruiser

• FJ40, FJ45, FJ43, FJ47, BJ40, BJ42, BJ45, BJ43, BJ44, BJ47, HJ40, HJ45, HJ43 and HJ47

Toyota Publica 

• KP30, KP31, KP36V, KP37V, KP38, KP39 and KP50

 Toyota Carina

• TA10
• KA67
• ET176V, AT170, AT175, ST170, ST170G, CT170, CT170G and CT176V

Toyota Cressida

• TX30, RX30, RX32, RX35, MX30, MX35, MX40, MX41, MX45, MX32 and MX36
• TX67V, SX60, RX63, RX60, GX61, GX60G, GX61, MX61, MX62, MX63, LX60, LX67V and LX65

 Toyota Hilux and Toyota Surf

• All models to N190 series

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Genuine Eagle brand 5mm Leads to suit your AT160 Toyota Celica built from 1985 to 1989

Our photo shows each of the boot and tube assemblies specific to this kit that suits the AT160 Toyota Celica.

Suits 1.6L 4A-GE DOHC models of the AT160 Toyota Celica.

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

• Hi-temp Silicone Well Cover boot
• PVT insulator tube insulates plug terminal to prevent high voltage crossover
• Hi-temp Silicone Tip Seal.

Terminal Features

• High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
• Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
• Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

• Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
• High Dielectric Silicone inner jacket.
• Technologically advanced nylon tape adds tensile strength.
• 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

Genuine Eagle brand 7mm Leads to suit your ST165 Toyota Celica built from 1986 to 1989.

Our photo shows each of the boot and tube assemblies specific to this kit that suits the ST165 Toyota Celica GT-Four.

Suits 2.0L 3S-GTE DOHC 16V Fuel Injection Turbo models of the ST165 Toyota Celica GT-Four and also referred to as Turbo All-Trac (USA).

General description:

 A premium quality ignition lead set specifically designed as an upmarket replacement for OHC motors fitted with Boot and Tube component technology.

Being Eliminator series, they are fitted with 1300 ohms per metre Ferrite Spiral Core conductor which by induction design delivers peak voltage to the plugs ensuring almost complete combustion for super quick starts and smooth running.

Tested to ISO 3808 Standards.

Features - Boot & Tube Assembly Features*

• Hi-temp Silicone Well Cover boot
• PVT insulator tube insulates plug terminal to prevent high voltage crossover
• Hi-temp Silicone Tip Seal.

Terminal Features

• High Memory spring steel retaining clip for positive terminal locking at all RPM'S.
• Extra long .51mm base offers minimal heat transfer from plug tip to inner conductor. This ensures maximum cable life.
• Triple cable retaining ribs and "W" shaped crimp ensure superior cable retention.

 Cable Features

• Simply "the best" Stainless Steel wound Ferrite coated Spiral Core conductor yields ultra low resistance ensuring peak voltage delivery to the spark plugs.
• High Dielectric Silicone inner jacket.
• Technologically advanced nylon tape adds tensile strength.
• 260°C High Temp. modified Silicone outer jacket ensures complete protection against heat and engine bay contaminants.

Shipping wordlwide weekly - no problems for overseas buyers.

Toyota screw mounting grommet clip pack to suit various Toyota models - Corolla, Celica, Carina, Corona, Land Cruiser, Prado and  MR2.

These clips have a 16mm collar diameter, 18mm stem length and fit to a 10mm x 10mm square hole and are a plastic push in trim clips used to fasten bumper bars, wheel arches, splashguards, sill panels, mud flaps, fuel tanks and fuel pipes.

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota MR2

• SW20 and SW21

 Toyota Corolla

• AE95
• AE100, AE101, AE102, AE104, CE100, CE104, EE100 and EE101

Toyota Celica

• AT160, ST160, ST161, ST162, ST163, ST165 and ST182

 Toyota Carina

• ST160, ST162 and ST163

Toyota Corona

• AT150, AT151, CT150, ST150, ST151
• ST160 and ST162

Toyota Hilux

• RN120, RN121, VZN120, VZN130, VZN131
• KZN130, LN130, LN135, RN130, RN131, RN135, YN130, YN135
• KDN185, KZN185, RZN180, RZN185, VZN180, VZN185
• GRN210, GRN215, KDN215, KZN215, RZN210, RZN215, TRN210, TRN215, UZN210, UZN215, VZN210 and VZN215

Toyota Land Cruiser 

• FZJ100, FZJ105, HDJ100, HDJ101, HZJ105 and UZJ100

Toyota Prado

• KDJ90, KDJ95,KZJ90, KZJ95, LJ90, LJ95, RZJ90, RZJ95, VZJ90 and VZJ95

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Inner guard (fender) fastener clip pack to suit various Toyota models - Celica, Corolla, Camry, MR2, Carina, Caldina

These clips are used to fasten inner guards (fenders) to the outer guard and are screwed into place. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

• TA40, TA45, TA41, TA42, TA46, TA47, RA40, RA45, RA55, RA46, RA42 and RA43
• TA60, TA61, AA63, TA62, TA63, TA64, SA60, RA63, RA60, RA6, SA63, RA64 and RA65
• ST160, ST162, AT160, ST163, ST164 and ST165
• ST180, ST184 and ST185
• ST200, ST202, ST203, ST204 and ST205

 Toyota MR2

• AW10 and AW11
• SW20 and SW21
• ZZW30

Toyota GR Four Yaris

• GXPA16

Toyota Corolla

• AE81, AE82, AE85 and AE86
• AE90, AE92, AE93, AE94, AE95 and AE96
• AE101, AE102 and AE112 

 Toyota Camry

• SV10, SV11, SV12, CV10 and CV11
• SV20, SV21 and SV22

Toyota Caldina 

• ST191, ST195 and ST198

 Toyota Carina

• TA40, TA41, TA42, TA47, TA57, RA40, RA45, RA46, RA55 and RA56
• AA60, KA67V, AA63, TA60, TA61, TA67V, TA62, TA63, RA63, CA60 and CA67V
• ST162
• ET176V, AT170, AT175, ST170, ST170G, CT170, CT170G and CT176V
• AT192, AT190, AT191, ST190, ST195, CT190 and CT195
• AAT212, AT210, AT211, ST210, ST215, CT210, CT215, CT211 and CT216

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Front and rear floor carpet set for your ST165 Toyota Celica GT-Four.

Suited to all RHD Toyota Celica ST165 GT-Four and All-Trac built between 1985 to 1989 our carpet floor mats are patterned off the floor of an original ST165 GT-Four, are well fitting and made in Australia to the highest quality with a non-slip foam backing.

There are four mats included in the set and this includes the two front foot well mats and the two rear floor well mats. 

Displayed here in Blue with a grey edge binding on the passnger side mats and in Charcoal with grey edge binding for the driver side mats, these mats provide a look that has an OEM look and feel.

Available in loop or plush pile and fourteen different colours. Just use the drop down menus to select pile and colour.

NOTE: Colour swatches shown are on plush pile carpet and may differ slightly on loop.

Complete your 'fourth gen' Toyota Celica ST165 project in style - whether its a daily driver, offroader or restoration project.

Shipping worldwide weekly - no problems for overseas buyers.

• Bark Bark
• Black Black
• Blue Blue
• Brown Brown
• Buckskin Buckskin
• Burgundy Burgundy
• Charcoal Charcoal
• Chevy Chevy
• Ginger Ginger
• Green Green
• Kingfisher Kingfisher
• Red Red
• Slate Slate
• Spindrift Spindrift
•  

• Edge binding colours Edge binding colours
• 
•  

Toyota bonnet (hood) support rod clamp to suit various Toyota models - Aurion, Camry, Corolla, Hilux, Land Cruiser, Prado, Starlet, Carina, Surf, 4Runner and Corona

These clamps a fit to a 14mm hole size, have a clamp size that holds rod diameter of up to 8mm and are a plastic push in clip used to hold the support rod when the bonnet (hood) is closed.

Can be purchased in packs of 1, 5 or 10 pieces - use the drop down menu.

Suits the following models:

Toyota Aurion / Toyota Camry

• CV10, CV11, SV10, SV11, SV12
• MCV20, MCV21, SXV20, SXV23, SXV25
• MCV36, ACV36
• ACV40, ACV41, ACV45, AHV40, AHV41, ASV40 and GSV40

Toyota Celica

• TA40, TA41, TA42, TA45, TA46, TA47, RA40, RA42, RA43, RA45, RA46, RA55
• AA63, TA60, TA61, TA62, TA63, TA64, SA60, SA63, RA60, RA61, RA64, RA65
• AT160, ST160, ST161, ST162, ST163, ST165
• AT180, ST182, ST183, ST184, ST185
• AT200, ST202, ST203, ST204, ST205
• ZZT230 and ZZT231 

Toyota Corona

• RT100, RT104, RT105, RT106, RT108, RT109, RT110, RT111, RT112, RT118, RT119, RT122, TT121, TT125, TT126
• RT130, TT130, XT130, TT131, RT131, TT132, RT132, RT133, RT 134, RT135, RT137V, TT138V
• AT140, ST140, TT140, AT141, RT141, ST141, TT141, RT142, TT142, KT147V, TT147V
• T160, T170, T190 series
• T200, T210, T220 series

Toyota Cressida

• RX37V, RX30, RX32, RX35, TX30, MX30, MX32, MX35, MX36,MX40, MX41, MX45
• X60, X70 and X80 series

Toyota Carina

• A10, A40, A60 series
• T150, T160, T170, T180, T200 and T210 series

Toyota Corolla

• KE30, KE35, KE38, KE55, TE55, TE37
• KE70, KE73G, KE71V, KE72V, KE74V, AE70, TE73V, TE71, TE70, TE72, CE70, CE71V
•  AE80, EE80, AE81 AE85, AE82, AE86, CE80
• AE90, AE92, AE93, AE94, AE95, AE96
• AE101, AE111, AE112
• ZRE120
• AZE141, CE140, NZE141, ZRE141, ZRE142, ZRE143, ZZE142
• ADE150, NDE150, NRE150, ZRE151, ZRE152, ZRE153
• ZRE172, ZRE173
• NDE180, NRE180, ZRE181, ZRE182 and ZWE182

Toyota Hilux / SURF / 4Runner

• RN10, RN15
• RN20, RN25
• RN30, RN35, RN40, RN45
• RN50, RN60, YN60, LN60, RN70, YN70, LN70
• N80, N90, N100, N110 series
• N120 series
• N130 series
• N140 series

Toyota Land Cruiser 

• FJ40, FJ41, FJ42, FJ43, FJ44, FJ45, FJ46, FJ47, BJ40, BJ41, BJ42, BJ43, BJ44, BJ45, BJ46, BJ47, HJ40, HJ41, HJ42, HJ43, HJ44, HJ45, HJ46, HJ47
• FJ55, FJ55G, FJ55V, FJ56
• FJ60, FJ62, FJ62G, FJ62RG, BJ60, HJ60, HJ61
• FJ80, HDJ80, HDJ81, HZJ80, HZJ81, FZJ80
• HZJ105, FZJ105, FZJ100, UZJ100, HDJ1001, HDJ1002.

Toyota Prado

• J90, J120 and J150 series

Toyota Starlet

• KP60, KP61, KP62
• P70, P80 and P90 series

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Complete your Toyota restoration project in style with a reproduction Toyota (TMC) Build Plate for vehicles built after 1980.

These TMC Build Plates were fitted in the engine bay of all early model Toyota's built from the 1980's right up until recent years - this may vary on some models.

We have seen these on Celica, Supra, MR2, Soarer, Corolla, Aristo, Starlet, Hilux and Landcruiser just to name a few models.

You may find that your original plate is missing (these are not a VIN!) as an owner may have removed it for painting of sometimes they have corroded and are no longer legible.

The plate was used to inform the production line workers as to what model engine was to be fitted to the vehicle - part of Toyota's quality program!

Our reproduction part is exacting in every detail. 

The pricing includes having your car's data applied to the plate before we ship it to you.

We ship globally to all countries weekly.

Radiator support to bonnet (hood) rubber seal fastener clip pack to suit various Toyota models - Celica, Corolla, Corona, Cressida, Land Cruiser, MR2, Hilux, Starlet and Supra

These clips are used to fasten the rubber strip that sits between the bonnet (hood) underside and top of the radiator support panel to reduce wind and water coming into the under bonnet (hood) area. 

Can be purchased in packs of 10 or 20 - use the drop down menu.

Suits the following models:

Toyota Celica

• TA40, TA45, TA41, TA42, TA46, TA47, RA40, RA45, RA55, RA46, RA42 and RA43
• TA60, TA61, AA63, TA62, TA63, TA64, SA60, RA63, RA60, RA6, SA63, RA64 and RA65
• ST160, ST162, AT160, ST163, ST164 and ST165
• ST180, ST184 and ST185
• ST200, ST202, ST203, ST204 and ST205

Toyota Corolla

• All models from KE30 through to ZWE182

 Toyota Corona

• All models from ST140 through to ST215

Toyota Cressida

• All models from MX32 through to RX81

Toyota Hilux and Surf

• All models from LN130 through to VZN185

Toyota Land Cruiser

• All models from BJ60 through HZJ105

Toyota MR2

• AW10 andAW11
• ZZW30

 Toyota Supra

• GA70, JZA70 and MA70
• JZA80

Toyota Starlet

• KP60, KP61

Our clips are European made and are well fitting suited to restorers and repairers.

Shipping worldwide weekly - no problems for overseas buyers.

Reproduction pair of amber or custom clear or smoke side marker indicator lenses for your fourth generation T160 series Toyota Celica.

Suited to all Toyota Celica T160 series built between 1985 to 1989 these lenses are wonderful in original amber or custom clear or smoke reproductions made to the highest quality and replace original part 20-149.

These lenses are fitted to the front mudguard (fender) of the AT160, ST160, ST161, ST162, ST163 and ST165 Toyota Celica and replace the traditionally amber lenses. Clear and smoke lense must be used with an amber bulb. Vendor does not warrant regulatory compliance.

Complete your 'fourth gen' Toyota Celica project in style - whether its a retro-ride, drift car, daily driver, restoration project or even a race car!

These lenses have been manufactured using precision tooling to produce a high quality faithful reproduction item.

UK and Europe customers please contact Toyota Heritage prior to ordering.

Shipping worldwide weekly - no problems for overseas buyers.

• Amber lenses Amber lenses
• Clear lenses Clear lenses
• Smoke lenses Smoke lenses
•